Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Pobierz pdf (Strona 66)

Digital Monitoring Products XR100 Series Programming Guide

Appendix

21.1 False Alarm Reduction

System Recently Armed report

TheSystemRecentlyArmedreport(S78)issenttothereceiverwhenaburglaryzonegoesintoalarmwithin

two minutes of the system being armed.

21.2 Diagnostics function

The XR100 Series panel contains a Diagnostics function that allows you to test the communication integrity

oftheLX-Bus™,identifyindividualzones,andalsodisplaythepresentelectricalstateofanyzone.The

Diagnostics function also allows you to test the integrity of the cellular communication, cellular signal,

andemailcommunication.TouseDiagnostics,resetthepanel,entertheDiagnosticscode2313(DIAG),and

press COMMAND.

Test LX-Bus

This function allows you to test the ability of the481,462N,463C,464-263Cor464-263HInterfaceCardsto

communicatewithzoneandoutputexpandermodulesconnectedtotheirLX-Buscircuits

. Press any top row

Select key when TEST LX-BUS displays.

The keypad displays LX-BUS:.Usingthedigitkeys,entertheLX-Busnumber1totestthatLX-Buscircuit.

The keypad now displays ADDRESS: -.Entera2-digitLX-BusdeviceaddressandpressCOMMAND.When

testingLX-Busdevices,enteronlytheaddressestowhichthemoduleshavebeenset.

Important Note: Adeviceaddressisnotthesameasazonenumber.Ifyouaretesting714or715Zone

ExpanderModules,whicheachcontainfourzones,thedeviceaddressistherstzonenumber.Whenthe

panelpollsa714ontheLX-Bus,itrecognizesitasafourzonedeviceanddoesnotpolltheremainingthree

zones.The714moduleinternallypollstheremainingzonesandtransmitsanystatuschangestothepanel.

ThisgreatlyreducestheamountoftimeittakesthepaneltopollallLX-Busdevices.

The keypad next displays TESTING . . . STOP during the device testing. At any time, you can Select STOP

to end polling. The panel records the number of no responses from the device. If all polls are received back

by the panel correctly, the keypad displays 00000/65535 FAIL.

If one or more polling attempts fail, the keypad displays * * * * */65535 FAILwiththe*representingthe

number of failed polling attempts. A display of 65535/65535 FAIL indicates a problem with the interface

cardoritsLX-Buswiringsuchasabadorbrokenwire,harnessnotproperlyconnected,orexcessivenoise

or distance. It can also mean that a zone number was entered that did not match a device address. Press

the Back Arrow key to enter a new device address or press COMMAND to exit the TEST LX-BUS.

Zone Finder

ThesecondDiagnosticfunctionistheZoneFinder.PressCOMMANDtodisplayZONE FINDER. This function

allowsyoutoidentifyindividualzonesondevicesconnectedtotheLX-Busofaninterfacecard,thepanel,

or any zones on the keypad data bus. To use ZONE FINDER, press any top row Select key. The display

changes to FAULT ZONE. The next zone on the system that changes from a normal to an open or shorted

state is displayed as ZONE NO: * * *. To continue, press the Back Arrow key.

Zone State

Press the COMMAND to display the third Diagnostic function: ZONE STATE. This function allows you to

enteranyzonenumberandcheckitscurrentelectricalstate(Normal,Open,orShorted).PressanySelect

key. The display changes to ZONE NUMBER: _.Enterinthezonenumberyouwanttocheckandpress

COMMAND. The panel displays the current state of the zone as NRML(normal),OPEN, or SHORT.

LX-Bus Status

The fourth Diagnostic function is the LX-BUS STATUS. This function allows the panel to poll all devices

connectedtotheLX-BusofaninterfacecardandcheckforanyOverlapped,Missing,orExtraaddresses.

Below is a description of each status item:

Overlap -Anoverlapoccurswhenonedeviceaddressisthesameasanyofthelastthreezonesonanother

714or715.Theoverlapfeaturecannotdeterminewhentwodeviceshavethesameaddress.

Example: Model714Address00=Zones500501502503,andtheModel711Address02=Zone502.

Zone502wouldreportasanOverlapbecauseboththe714and711havedevicessetto502.

Missing -Amissingoccurswhenazonebetween500and599hasbeenprogrammedinZONE INFORMATION

andnodevicewiththatzoneaddresshasbeeninstalledontheLX-Bus.Tocorrecttheproblem,checkyour

zone programming and zone expansion module addressing.

Extra -AdeviceisinstalledontheLX-Busbutnoneofitszonesareprogrammedintothesystem.

MAC Address

ShortforMediaAccessControladdress.Thishardwareaddressuniquelyidentieseachnetworknode.Not

to be confused with an IP address, which is assignable. In the Diagnostics function, the MAC address is the

panelon-boardnetworkhardwareaddress.PressanytoprowSelectkeytodisplaythepanelMACaddress.

Press the COMMAND key to view the next option.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Strona 66

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadian XR100