Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Pobierz pdf (Strona 50)

Digital Monitoring Products XR100 Series Programming Guide

AreA InformAtIon

Area Information

17.1

AREA INFORMATION

Area Information

Allowsyoutoassignfunctionstothedifferentareasinthesystem.Allnon-24-hour

zonesmustbeassignedtoanactivearea.SeeZoneInformation.

You activate an area by assigning it a name. See Area Name. A name is given

to each active area in place of a number to assist the user during arming and

disarming.TheArmedStatusdisplayis12345678.

17.2

EXIT DELAY: 60

Exit Delay

EntertheexitdelaytimeforallExittypezonesinthisarea.Whentheexitdelay

timestarts,allactivityonthatzoneandothernon-24-hourzonetypesinthearea

isignoreduntiltheexitdelayexpires.ThekeypaddisplaystheExitDelaytime

countdownandannunciatestheExitDelaytoneat8secondintervalsuntilthelast

10secondswhenannunciationisat3secondintervals.

Theexitdelaycanbefrom30to250seconds.Defaultis60seconds.

DuringExitDelay,ifanexitzonetrips,thenrestores,andtripsagain,theExit

Delaytimerrestarts.Thisrestartcanoccuronlyonce.TheExitDelayrestartis

disabledwhenprogrammedforULAAHighLineSecurityoperation.

Exit Error Operation: At arming, whenanentry/exitzone(EX)is faulted at the

end of the exit delay then one of two sequences occur:

ForEntryDelay1EXtypezones:

•thebellsoundsforthelengthoftimesetinBellCutoffprogramming.

•theEntryDelayoperationstartsrequiringcodeentrytodisarm

•ifnotdisarmed,azonealarmandanexiterroraresenttothereceiver.

ForEntryDelay2-4EXtypezones:

•thezoneisforcearmedandazoneforcearmmessageissenttothereceiver

•anExitErrorissenttothereceiver

•thebellsoundsforthelengthoftimesetinBellCutoffprogramming

17.3

BURG BELL OUT: 0

Burglary Bell Output

Entertheoutputnumber(0to6,500to599,G1toG20,orD1toD8)thatisturned

on any time a Burglary type zone is placed in alarm. The output is turned off when

you disarm any area and no other Burglary type zones are in alarm. The output can

alsobeturnedoffusingtheAlarmSilenceoptionintheUserMenuorbyentering

a user code with the authority to silence alarms. The duration of this bell output

follows the time entered in the System Options>Bell Cutoff Time option. See the

Output Options - Bell Cutoff Time section. If Bell Test is selected YES, the Burglary

Bell Output entered here is turned on for two seconds each time the system is

armed.

17.4

O/C RPTS NO YES

Opening/Closing Reports

This option allows an Opening report to be sent to the receiver whenever any area

is disarmed. A Closing report is also sent to the receiver when any area is armed.

17.5

CLS CHK NO YES

Closing Check

SelectYEStoenablethepaneltoverifythatallareasinthesystemarearmed

afterpermanentorextendedschedulesexpire.IftheClosingCheckndsanyareas

disarmed past the sched uled time, the keypads selected to display System Trouble

StatusdisplaysCLOSINGTIME! and emits a steady beep. When Area Schedules is set

toYESinAreaInformation,thespecicareaandnamedisplayfollowedby—LATE.

When Auto Arm is NO, if within ten minutes the system is not armed or if the

scheduleisnotextended,aLatetoClosereportissenttotheSCS-1/SCS-1R

Receiver.WhenAutoArmisYES,theareaarms.SeeAutomaticArmingsection.

If the area becomes disarmed outside of any schedule, the Closing Check sequence

occursaftertheLateArmDelaytime.SeeLateArmDelay.

PC LOG REAL-TIME

STATUS

NO YES

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Strona 50

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadian XR100