Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Pobierz pdf (Strona 16)

Digital Monitoring Products XR100 Series Programming Guide

CommuniCation

Communication

3.1

COMMUNICATION

Communication

Congurethecommunicationoptionsforthepanel.Theinformationyouprogram

varies with the Communication Type you select.

3.2

ACCOUNT NO: 12345

Account Number

The Account Number is a 1 to 5 digit number used to identify which panel is sending

amessage.EntertheaccountnumbersenttotheSCS-1RReceiver.Messagesmay

besenttoacentralstationorviaPCLogReportstoaPC.Thedefaultis12345.

NET, CELL, and DD -Therangeofvalidaccountnumbersforapanelis1to65535.

For accounts of four digits or less, do not enter leading zeros.

CID - Chooseanaccountnumberbetween1and9999.

3.3

XMIT DELAY: 30

Transmit Delay

Enterthenumberofseconds(15to45)thepanelwaitsbeforesendingburglary

zones(Night,Day,orExit)reportstothereceiver.Otherzonetypereportsare

sent immediately. Alarm bells and relay outputs are not delayed during this period.

ProgramBurglaryOutputsforpulsedorsteady,andsetAbortReportstoYESif

OpeningandClosingreportsarenotbeingsent.Enter0(zero)todisablethis

function.Thedefaultis30.

If the area where the alarm occurred is disarmed during the Transmit Delay time,

onlyanAbortReport(S45)messageissenttothereceiver.Iftheareawhere

the alarm occurred is disarmed after the alarm message is sent to the receiver

but before the Bell Cutoff time expires even if the alarm was silenced, an Alarm

Cancelled(S49)messageissent.Otherwisethealarmissentattheendofthe

delay. The Alarm Cancelled report cannot be disabled.

Note: For Commercial Burglary Installations, the combined Transmit Delay

(Abort Window) and Entry Delay must not exceed one (1) minute.

3.4

PATH: -

Communication Path

Uptoeightcommunicationpathsmaybeprogrammed.Eachpathisdesignatedas

a primary or backup communication route. Path 1 is always Primary but other paths

may be programmed as additional primary or backup.

Eachprimarypathestablishesanewpathgroup.Apathgroupismadeupofthe

primary path and its subsequent backup paths. Typical communication takes place

on the primary path with backup paths being used only when the primary path fails

or when the backup path is programmed to duplicate messages. There is no option

tobackuppath8.

3.5

COMM TYPE: DD

Communication Type

Speciesthecommunicationmethodthepanelusesonthispathtoreportsystem

eventstoDMPSCS-1RReceiversornon-DMPreceivers.DefaultisDDforPath1,and

NONEforPath2-8.

NONE - Forlocalsystems.SelectingNONEendscommunicationprogramming.

DD - DigitalDialercommunicationstoaDMPSCS-1RReceiver.

NET - Network communication using the panel onboard network connection. The

DMPNetwork/Outputreportingformatistransmittedoveradatanetworktothe

SCS-1RReceiver.

CID - Thisoptionallowsthepaneltocommunicatetonon-DMPreceiversusingthe

Contact ID format.

CELL - Thisoptionallowscommunicationoverthecellularnetworkusingthe463C,

464-263Cor464-263HCellularCommunicators.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Strona 16

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadian XR100