Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Pobierz pdf (Strona 27)

XR100 Series Programming Guide Digital Monitoring Products

Device Setup

6.14

OVERRIDE NO YES

Schedule Override

UsethisoptiontoallowdoorON/OFFschedulestobeoverriddenbythearmedcondition

of the system. Selecting YES causes the on time for a door schedule to be ignored when

all areas assigned to Access Areas for this device are armed. Should any area become

disarmed after the door schedule on time, the device output turns on. A door output

which is on during a disarmed period automatically turns off when all access areas

assigned to the device become armed, even if the scheduled off time has not been

reached. This feature can be used to keep doors locked when a factory opens late, or

is forced to close early, due to a snow storm or other cause. Select NO to allow door

schedules to operate independent of system armed status.

Note: When OVERRIDE is YES and there are no areas programmed in ACCESS AREAS,

thedoorscheduleforthatdevicedoesnotwork.EithersetOVERRIDE to NO or enter an

area number in ACCESS AREAS.

6.15 Auto Force Arm Device?

Select YES to have all Display Areas assigned to this keypad automatically arm and force

arm faulted zones at arming. The user is not prompted to select areas to arm or force

arm faulted zones after choosing ARM at the keypad. If Closing Code is programmed as

YES,onlythematchingareasbetweentheDisplayAreasandtheUserCode’sauthorized

areas arm. Also, when YES is selected, the user is not prompted to select areas to

disarmafterenteringacodeatEntryDelayorafterchoosingDisarmatthekeypad.

AllmatchingareasassignedtotheUserCodeandtothiskeypadareautomatically

disarmed. When NO is selected,theuserispromptedtoselectareas(ALLNOYES)and

choose to force arm or bypass at arming and disarming. Default is NO.

6.16 Door Real-Time Status?

Select YES tohavereal-timedoorstatusmessagessenttoPCLogreportingandEntré

reporting for this device. Messages are sent anytime the panel turns the door relay on

or off. Default is NO.

6.17 Send Door Forced Message?

Select YES tohavethepanelsendareal-timedoorstatusmessageofForcedOpen(FO)to

PCLogreportingandEntréreporting

when the door relay is off, but the door zone has

transitioned from its normal state. Default is NO.

6.18 Program 734/734N Options

Select YES toprograma734ora734N/734N-WiFiWiegandInterfaceModule.Theoptions

displayedfora734ora734N

are the same.

Toprograma734,theDevicetypemustbesettoDOORandtheDeviceCommunication

TypemustbesettoKPDBUS.

Toprogramthe734N/734N-Wi,theDeviceTypemustbesettoDOORandtheDevice

CommunicationTypemustbesettoNETWORK.

6.18.1 Activate Zone 2 Bypass

SelectYEStoactivatetheBypassoption.

SelectingNOallowsstandardzoneoperationonZone2anddisplaystheACTIVATEZONE

3REXoption.DefaultsettingisNO.

Ifthedoorbeingreleasedbythe734/734N\734N-WiFimoduleisprotected(contact

installed),youcanprovideaprogrammableBypassentry/exittimerbyconnectingits

contactwiringtoa734/734N/734N-WiFimoduleZone2.Whentheon-boardFormCrelay

activatesandtheuseropensthedoorconnectedtoZone2,thezoneisbypassedforthe

numberofsecondsprogrammedinZONE2BYPASSTIMEallowingtheusertoenter/exit.

IfZone2doesnotrestore(doorclosed)withintheprogrammedbypasstime,the

734/734N/

734N-WiFi

piezopulsesduringthelasttenseconds.IfZone2restoresprior

to the end of the programmed time, the piezo silences. If the zone does not restore

beforetheprogrammedtime,the734/734N/

734N-WiFi

ends the bypass and indicates

the open or short zone condition to the panel.

6.18.2

ZONE 2 BYPASS

TIME: 40

Zone 2 Bypass Time

EnterthenumberofBypasssecondstoelapsebeforetheBypasstimerexpires.Rangeis

from20to250seconds.Pressanytoprowselectkeytoenterthenumberofseconds.

Ifthedoorremainsopenwhenthetimerexpiresazoneopen/shortissenttothepanel

forZone2.Thedefaultis40seconds.

6.18.3

RELOCK ON ZONE 2

CHANGE? NO YES

Relock on Zone 2 Change?

SelectingNOleavestherelayonwhenZone2faultstoanopenorshortcondition

duringBypass.SelectingYESturnsthe734/734N/

734N-WiFi

relayoffwhenZone2

changes state. The default is NO

AUTO FORCE ARM

DEVICE? NO YES

DOOR REAL-TIME

STATUS? NO YES

SEND DOOR FORCED

MESSAGE? NO YES

PROGRAM 734

OPTIONS? NO YES

ACTIVATE ZONE 2

BYPASS? NO YES

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadian XR100