Digital Monitoring Products Canadian XR100 Instrukcja Obsługi Strona 28

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 78
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 27
Digital Monitoring Products XR100 Series Programming Guide
20
Device Setup
6.18.4
ACTIVATE ZONE 3
REX? NO YES
Activate Zone 3 Request to Exit
SelectingYESactivatestheZone3RequesttoExit(REX)option.
SelectingNOallowsstandardzoneoperationonZone3anddisplaystheACTIVATE
ONBOARDSPEAKERoption.DefaultsettingisNO.
OptionallyconnectaPIR(orothermotionsensingdevice)oramechanicalswitchto
Zone3toprovideREXcapabilitytothesystem.WhenZone3shorts,theon-board
Form C relay activates for the programmed number of seconds. During this time,
theusercanopentheprotecteddoortostarttheprogrammedBypass™entry/exit
timer. After the programmed number of seconds, the relay restores the door to its
locked state.
The734/734N/
734N-WiFi
moduleprovidesabypass-onlyoptionforREXonZone3.
WhenZone3opensfromanormalstate,onlyaBypassoccurs:theon-boardrelay
doesnotactivate.Thisbypass-onlyoptionusestwomethodsofREX.TherstREX
deviceprovidestheprogrammedBypassentry/exittimer.ThesecondREXdevice,
or manual device such as a door knob, unlocks the door.
Anexampleofthebypass-onlycongurationisadoortoanofcethatislocked24
hoursaday.UserspassaREXmotiondetectorpositionedbythedoortobeginthe
programmed exit timer. Within the programmed number of seconds the user must
thenmanuallyactivateaseconddevice,suchasaREXdeviceormanualdoorknob,
to unlock the door. If the door is opened after the programmed number of seconds,
the zone goes into alarm.
6.18.5
ZN 3 REX STRIKE
TIME: 5
Zone 3 REX Strike Time
EnterthenumberofREXsecondstoelapse.Rangeisfrom5to250seconds.Press
any top row select key to enter the number of seconds. The default is 5 seconds.
PresstheCOMMANDkeytomoveforwardtotheACTIVATEONBOARDSPEAKERoption.
TheBackArrowreturnstoACTIVATEZONE3REX.
6.18.6
ACTIVATE ONBOARD
SPEAKER? NO YES
Activate Onboard Speaker
SelectYEStoenabletheonboardpiezospeakerforlocalannunciation.SelectNOto
turn the piezo off for all operations. This does not affect remote annunciator open
collector(RA)operation.ThedefaultisNO.
6.18.7
CARD OPTIONS:
DMP
Card Options
Press any top row Select key to display options. Press the select key under DMP,
CUSTOM,orANYtoselectthatoption.SelectDMPtoindicatethereadersendsa
26-bitDMPdatastring.PresstheCOMMANDkeytodisplayREQUIRESITECODE.
Note: When set to DMP, the 734/734N/734N-WiFi converts 17 bits of the 26-bit
data string into a 5-digit number.
SelectCUSTOMifusinganon-DMPcardorusercodelengthof6to10digits.
Default is DMP.
Select ANY to allow all card reads to activate the door strike relay. The door strike
relayisactivatedforthelengthoftimeprogrammedinZN3REXSTRIKETIME.No
user code information is sent to the panel.
Custom Card Denitions
6.18.8 Wiegand Code Length
When using a custom credential, enter the total number of bits to be received in
Wiegand code including parity bits.
PressanytoprowSelectkeytoenteranumberbetween1-255toequalthenumber
ofbits.Defaultis26bits.
Typically,anaccesscardcontainsdatabitsforasitecode,ausercode,andstart/
stop/paritybits.Thestartingpositionlocationandcodelengthmustbedetermined
andprogrammedintothe734/734N/
734N-WiFi
.
CARD OPTIONS:
DMP CUSTOM ANY
WIEGAND CODE
LENGTH: 26
01110101101101010001100111
First Bit
Received
Position = 0
Site Code
Position = 1
Length = 8
User Code
Position = 9
Length = 16
Last Bit
Received
Position = 25
In this example the Wiegand Code Length = 26 bits.
Przeglądanie stron 27
1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag