Digital Monitoring Products Canadain XR500 Instrukcja Obsługi Pobierz pdf (Strona 56)

Digital Monitoring Products XR500 Series Programming Guide

AreA InformAtIon

18.17

LATE OUTPUT: 0

Late Output Number

Enter the output to turn on when this area is not armed by its scheduled time and Area

Late or Closing Time displays at a keypad and the keypad buzzer is on. The output is

turned off when the keypad buzzer is silenced by pressing any key. Default is 0 (zero).

18.18

LATE/ARM DLY: 60

Late Arm Delay

Enter 4 to 250 minutes to delay before automatic re-arming occurs after the area

becomes disarmed outside of schedules. See Closing Check. Default is 60 minutes.

Note: The Late Arm Delay can be superseded by the Re Arm Delay setting of the User

Prole assigned to the user who disarmed the area. Refer to the Re Arm Delay section in

the XR500 Series User’s Guide (LT-0683).

18.19

BANK/SAF NO YES

Bank Safe & Vault (XR500N/XR500E only)

NO disables the Bank Safe & Vault feature for this area. When selected as YES, schedules

set for this area and the time of day cannot be changed while the area is armed.

Program schedules before arming: A Bank Safe & Vault area can only be disarmed

during scheduled times. If the area becomes armed before programming a schedule, the

panel must be reset before the area can be disarmed from a keypad or the Bank Safe &

Vault option in Area Information must be set to NO.

Zones assigned to Bank Safe & Vault areas cannot be bypassed or force armed. Do not

assign Bank Safe & Vault area to an Arming zone. Arming zones can disarm Bank Safe &

Vault areas outside of a schedule.

18.20

COMMON NO YES

Common Area

Select YES to enable this area to operate as a common area. This area is armed when

the last area in the system is armed and is disarmed when the rst area in the system is

disarmed. You can have multiple common areas in each system. For the common area to

work properly, do not assign the common area to any user code. When a user code can

arm and disarm the common area from a keypad at any time, the common area does not

function as a common area.

18.21

ARM FIRST NO YES

Arm First Area

Select YES to enable this area to operate as an Arm First area. This area is automatically

armed when any non-Arm First area assigned to the same keypad is armed but does not

disarm when other areas become disarmed. Assign areas to keypads using the Display

Areas option in Device Setup programming. You can have multiple Arm First areas in a

system and divide them among keypads if needed. If an Arm First area has faulted zones

that cannot be bypassed, arming stops and the areas are not armed. Correct the problem

with the Arm First area and then begin the arming process again. Default value is NO.

Note: The Arm First automatic arming only occurs when arming from a keypad.

Arming from a zone, schedule, or remotely is not affected and Arm First areas do not

automatically arm.

18.22

TWO MAN NO YES

Two Man Rule (XR500N/XR500E only)

Select YES to require two user code entries to disarm and/or allow door access to this

area. When a user presents a code to a keypad or reader requesting a door access or

disarm, 2ND CODE displays and requires the entry of a different user code with at least

the same authority. The second user code must be entered within 30 seconds.

NO disables the Two Man Rule for this area.

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 83 84

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadain XR500 Instrukcja Obsługi Strona 56

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadain XR500