Digital Monitoring Products Canadain XR500 Instrukcja Obsługi Pobierz pdf (Strona 55)

XR500 Series Programming Guide Digital Monitoring Products

AreA InformAtIon

18.11

* UNUSED *

Area Name

The area name can be up to 32 alphanumeric characters. To add an area name to the system,

press any Select key and then enter up to 32 characters for the new area name. Press

COMMAND to continue. For instructions on entering alphanumeric characters see section 1.7

Entering Alpha Characters. Inactive areas are marked * UNUSED *. Only systems programmed

for Area arming have the option available to change the area name.

To mark an active area unused, press any top row Select key to delete the old name,

then press the COMMAND key. The programmer automatically programs the name as

*UNUSED*. If you have already cleared Area Information during Initialization, all areas are

marked * UNUSED *. See Initialization section.

Home/Sleep/Away with Guest systems display the area name, but the names cannot be

changed. The following are the display names that appear on the keypad:

Area Display Area Display Area Display

1 Perimeter 4 Guest1 Perimeter 7 Guest2 Perimeter

2 Interior 5 Guest1 Interior 8 Guest2 Interior

3 Bedrooms 6 Guest1 Bedrooms 9 Guest2 Bedrooms

18.12

ACCOUNT NO: 12345

Account Number

Enter the account number to be sent to the receiver for this area. Choose an account

number compatible with the Communication Type selected in Communications. The default

Account Number is the one previously entered in Communications. This account number is

used when sending area messages and events to the central station

See the Area Account

Number Messages in the Appendix.

18.13

AUTO ARM NO YES

Automatic Arming

Select YES to allow this area to arm automatically according to permanent, temporary, or

extended schedules. If no schedules are programmed, the area auto arms every hour.

If closing check is selected as YES, the automatic arming function does not take place

until the expiration of a ten minute Closing Check delay. See Closing Check. If the area

has been disarmed outside of any permanent or temporary schedule, the closing check

sequence occurs one hour after the area is disarmed.

At arming, bad zones are handled according to the option selected in section Bad Zones.

If a closing report is sent, the user number is indicated as SCH on the SCS-1R Receiver.

NO disables automatic arming for this area.

Note: For ANSI/SIA CP-01 UL installations, Automatic Arming cannot be used for arming.

18.14

BAD ZONES: BYP

Bad Zones

At the time of automatic arming, some zones in the area may not be in a normal

condition. This option allows you to program the panel response to these bad zones. This

option does not display if AUTO ARM is NO.

BYP FORC REF

BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if Bypass

Reports is YES. The report indicates SCH as the user number.

FORC - All bad zones are force armed. Zones force armed in a bad condition are capable

of restoring and reporting an alarm if tripped. A forced zone report is transmitted if

Bypass Reports is YES. The report indicates SCH as the user number.

REF - The automatic arming is refused and no arming takes place. A No Closing report is

sent to the receiver regardless of the Closing Check selection.

18.15

AUTO DIS NO YES

Automatic Disarming

NO disables automatic disarming by schedule for this area. When YES is selected, the

area automatically disarms according to permanent or temporary schedules. If an

opening report is sent to the receiver, the user number is indicated as SCH.

Note: For ANSI/SIA CP-01 UL installations, Automatic Disarming cannot be used for

disarming.

18.16

ARMED OUTPUT: 0

Armed Output Number

Enter the output to turn on when this area is armed. If an exit delay is used for this area,

the Armed Output turns on at the start of the exit delay. The output is turned off when

this area is disarmed. The output cannot be turned on from the User Menu Outputs On/

Off option.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 83 84

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadain XR500 Instrukcja Obsługi Strona 55

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadain XR500