Digital Monitoring Products Graphic Touchscreen Podręcznik Użytkownika Pobierz pdf (Strona 22)

XR150/XR350/XR550 User’s Guide 15Arming and Disarming

Note: If your system uses a keyswitch to arm an area, the exit

delaytimedoesNOTshowonthekeypaddisplay.

When you arm both the Perimeter and Interior to leave the

building but then you do not exit by the time the exit delay ends,

thesystemautomaticallyarmsbuttheinteriorarea(s)willremain

disarmed because you have not exited.

Should you exit the building and the door does not close properly,

your system may be programmed so that when the exit delay

countdown ends, then the entry delay starts and the bell will sound

to alert you to the situation. Enter your user code to stop the bell

and disarm the system. Rearm the system, exit the building, and

make sure the door is securely closed.

ONE MOMENT . . . Message: If your system is monitored, it

may be programmed to wait for the arming report transmission

to the central station before displaying the armed mes sage. This

veriesyourphonelinesareworkingproperly.Whilethesystemis

waitingforthetransmission,thedisplayreadsONEMOMENT...If

the report is received, the keypad displays the armed message. If

thereportisnotreceived,thekeypaddisplaysLOCALALARMONLY

before displaying the armed message.

Note: Your system may be pre-programmed at installation to:

—sendarmingorzonebypassingreportstoacentralstation

—armand/ordisarmspecicareasatspecickeypads.

Key Fob Arming

Press and hold the key fob button programmed for Arming or the Toggle

arm/disarm button. The Red LED two-second acknowledgement light

indicatesAllSystemOn.TheGreen/Redtwo-secondacknowledgement

lightindicatesSystemOnwithsomeareasarmed.

Key Fob Disarming

Press and hold the key fob button programmed for Disarming

or the Toggle arm/disarm button. The Green LED two-second

acknowledgementlightindicatesAllSystemOff.

Area System Arming Operation

Area Assignment: Your security system has been set up into

separate areas. The number of areas and their names are listed on

the table in System Setup.

Arming the Area System

1. PresstheCOMMANDkeyuntilARMDISARMisdisplayed.

2. Select ARM to arm the system.

3. Enter your user code if required. The keypad displays

ALL?NOYES.

4. SelectNOtoarmonlyselectedareas.Gotostep5.Select

YES to arm all areas authorized for your user code. Go to

step6.

5. IfyouselectedNOinstep4,thedisplaybeginstolisteach

areatowhichyouhaveaccessfollowedbyNOYES.

 Example:OFFICENOYES

5a. Select YES for each area you want to arm.

5b. Select NO for each area you do not want to arm.

6. Thesystemdisplaysanybypassedzonesorfaulted24-hour

orPriorityzones.AfaultedPriorityzonecannotbearmed.

7. Atthispointyoucanforcearmorbypassanyfaultedzones.

Azonethatisforcearmedisrestoredintothesystemifitlater

returnsto normal.A zone that is bypassed remains bypassed

until the system is disarmed. See steps 7a through 7d.

7a. If a problem exists on a zone, the zone name and

problemisshownfollowedby:OKAYBYPASSSTOP.

7b. Select OKAYtoforcearmthefaultedzone.

7c. Select BYPASS to bypass all faulted zones being

displayed.

Note:24-hourzonescannotbebypassed.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 83 84

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Graphic Touchscreen Podręcznik Użytkownika Strona 22

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Graphic Touchscreen