Digital Monitoring Products Canadian XR100 Przewodnik Instalacji Pobierz pdf (Strona 34)

Digital Monitoring Products XR100 Series Installation Guide

COMPLIANCE

XR100 Series Installation Guide Digital Monitoring Products

COMPLIANCE

UL 864 NFPA 72 (Chapter 9) Specications

Control Units for Fire-Protective Signaling Systems

29.1 Zone Restoral Reports

The Restoral Reports option must be selected as YES or Disarm. See the XR100 Series Programming Guide (LT-0896).

29.2 Power Fail Delay

The Power Fail Delay option must be selected as required by the service of the panel. For Central Station service:

6-12, for Remote Station service: 12-15. See the XR100 Series Programming Guide (LT-0896).

29.3 Sprinkler Supervisory

Any zone used for sprinkler supervisory must be programmed with “SPRINKLR XXX” as the zone name. The last three

characters in the zone name may be assigned a number to identify the zone. The Model 893A Dual Phone Line Module

must be used on all sprinkler supervisory systems.

29.4 DACT Systems

Two phone lines must be used. The two phone lines cannot be ground start or party lines. The 893A Dual Phone Line

Module is used to provide two phone line connections to the system. The 2ND Phone Line communication option must

be selected as DD. See the XR100 Series Programming Guide (LT-0896).

Two different phone numbers must be programmed for digital communication. See the XR100 Series Programming

Guide (LT-0896). The Test Time option must be programmed so that the XR100 Series sends a report every 24 hours.

See the XR100 Series Programming Guide (LT-0896).

29.5 Local Protective Signaling Systems

The DMP Model 865, 866, or 867 Notication Circuit Module must be used on the bell circuit for detection of shorts

and grounds. See sections 33.1 to 33.2 in this guide for wiring diagrams. Model 790 series keypads that are used to

display troubles for local re alarm systems must be installed within a DMP Model 777 with 777S 1.0” spacer. Any

burglary or other off premises communication must be done with the Model 893A Dual Phone Line Module. For local

commercial re installations, the 893A is required.

29.6 Remote Station Protective Signaling Systems

You must provide 60 hours of standby battery. See section 6.9 in this guide for standby battery calculations. Two

Radionics Model D127 Reversing Relay Modules provide two reversing polarity telephone connections. See the D127

Installation Instruction sheet for wiring details. A DMP Model 893A is used to provide two line dialer communication.

29.7 Fire Protective Signaling Systems using Internet/Intranet Networks

The XR100N Command Processor™ Panel must be programmed as described below for Fire Protective Signaling

Systems using NET Communication Type.

• UL AA must be programmed as NO • RETRY TIME must be programmed as 1

• SUB CODE must be programmed as YES • FAIL TIME must be programmed as 1

• CHECKIN must be programmed as 1 • NET TRBL must be programmed as YES

29.8 Combination Systems

For combination re and burglary systems, powered burglary devices (PIR, Glassbreak, etc.) must be powered from

a separate UL Listed power supply (DMP Model 505-12). This requirement is not needed for non-powered burglary

devices (door contacts, etc.) which only connect to the zone input of zone expanders or keypads. Refer to 33.7

Powered Burglary Devices later in this document.

UL 985 NFPA 72 (Chapter 2) Specications

Household Fire Warning System Units

30.1 Bell Output Denition

The Model XR100 Series panel Bell Output must be programmed to operate steady on burglary alarms and pulsed or

temporal on re alarms. See the XR100 Series Programming Guide (LT-0896).

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 45 46

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadian XR100 Przewodnik Instalacji Strona 34

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadian XR100