Digital Monitoring Products Canadian XR100 Przewodnik Instalacji Pobierz pdf (Strona 22)

Digital Monitoring Products XR100 Series Installation Guide

INSTALLATION

XR100 Series Installation Guide Digital Monitoring Products

INSTALLATION

Protection Zones

10.1 Terminals 13–24

Zones 1 to 8 (terminals 13 to 24) on the XR100 Series panel are all grounded burglary zones. For programming

purposes, the zone numbers are 1 through 8. Listed below are terminal 13 to 24 connection functions.

Terminal Function Terminal Function

13 Zone 1 voltage sensing 19 Zone 5 voltage sensing

14 Ground for Zones 1 and 2 20 Ground for Zones 5 and 6

15 Zone 2 voltage sensing 21 Zone 6 voltage sensing

16 Zone 3 voltage sensing 22 Zone 7 voltage sensing

17 Ground for Zones 3 and 4 23 Ground for Zones 7 and 8

18 Zone 4 voltage sensing 24 Zone 8 voltage sensing

The voltage sensing terminal measures the voltage across a 1k Ohm End-of-Line resistor to ground. Use DMP Model

311 1k Ohm resistors. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normally-

open) with any of the burglary protection zones.

1K Ohm

Normally

Closed

1K Ohm

Normally Open

1K Ohm

Combination Normally Open

and Normally Closed

Figure 4: Protection Zone Wiring

10.2 Operational Parameters

Each protection zone detects three conditions: Open, Normal, and Short. Listed below are voltage and resistance

parameters for each condition:

Condition Resistance on zone Voltage on positive terminal

Open over 1300 ohms over 2.0 VDC

Normal 600 to 1300 ohms 1.2 to 2.0 VDC

Short under 600 ohms under 1.2 VDC

10.3 Zone Response Time

A condition must be present on a zone for 500 milliseconds before it is detected by the XR100 Series panel.

Ensure detection devices used on the protection zones are rated for use with this delay. Zones 1-10 can also be

programmed for a fast response delay of 160 milliseconds.

10.4 Keyswitch Arming Zone

Using a keyswitch on an Arming type zone allows you to arm and disarm selected areas without having to enter a

user code.

Powered Zones for 2-Wire Smoke Detectors

11.1 Terminals 25–26 and 27–28

Panel terminals 25 through 28 provide two resettable Class B, Style A, 2-wire powered zones. For programming

purposes the zone numbers are 9 and 10.

Note: The maximum wire length for either zone 9 or zone 10 is 3000 feet using 18 AWG or 1000 feet using 22 AWG.

When using 725 Zone Expansion Modules, use UL Listed Model 316 EOL resistors. The UL compatibility identier for

the zones using 725 Zone Expansion Modules is B. When using all other zone expansion modules, use UL Listed Model

309 EOL resistors. The UL compatibility identier for the zones is A.

Note: Do not mix detectors from different manufacturers on the same zone.

Caution: Performing a Sensor Reset momentarily drops power to the devices on Zones 9 and 10. The

panel views these zones (9 and 10) as “Open” while the power is absent.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 45 46

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadian XR100 Przewodnik Instalacji Strona 22

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadian XR100