Digital Monitoring Products Canadain XR500 Przewodnik Instalacji Pobierz pdf (Strona 26)

Digital Monitoring Products XR500 Series Canadian Installation Guide

InstallatIon

J1 Ethernet Connector (XR500N/XR500E only)

17.1 Description

The J1 Ethernet Connector is available on the XR500N/XR500E Network version to connect directly to an Ethernet

network using a standard patch cable. The maximum impedance is 100 Ohms.

17.2 Ethernet LEDs

The two LEDs, located to the left of J1 Ethernet Connector, indicate network

connection. The top, Link LED lights up green to indicate a valid receive

connectionfromthehostnetwork.Thebottom,ActivityLEDashesyellowto

indicate messages are being sent and received.

J3 Telephone RJ Connector

18.1 Description

Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel J3 connector

and the RJ31X or RJ38X phone block. The maximum impedance is 100 Ohms. CAUTION -Toreducetheriskofre,

useonlyNo.26AWGorlargertelecommunicationlinecord,suchasDMPModel356SeriesPhoneCords.

18.2 J10 893A Connector

Connect an 893A Dual Phone Line Module to J10 on the XR500 Series. Refer to the 893A Installation Sheet (LT-0135)

for complete information.

18.3 Notication

The user must not repair registered terminal equipment. In case of trouble, immediately unplug the device from the

telephone jack. The factory warranty provides for repairs. Registered terminal equipment may not be used on party

lines or in connection with coin telephones. No tify the telephone company with the following information:

a. The particular line(s) where the service is connected

b. This Class A digital apparatus complies with Canadian ICES-003.

c. The ringer equivalence

d. The device make, model, and serial number

18.4 Phone Line Monitor

The XR500 Series panel has a built-in telephone monitor that monitors the phone line voltage to verify the

connectiontothecentralofce.Figure11andthetablebelowidentifythephoneblockpinlayout,wirenumbers,

and colors.

Wire Number Wire Color

1 Gray

2 Orange

3 Black

4 Red

5 Green

6 Yellow

7 Blue

8 Brown

ThewiresontheRJ31thatfeedpins4and5shouldbetheONLYwiresontheD-marc.Allotherhousephonewiring

should be tied to pins 1 and 8 coming back from the RJ31.

DialtonemustcomeintoRJ31Xonpins4and5andgobacktohousephonesfrompins1and8.Followthesesteps

to determine if panel is seizing the line:

1. Unplug phone cord from RJ31X

2.Placebutt-setonpins4and5

3.Listenfordialtone.Withdialtonepresent,lifteitherwirefrompins1or8

4.Listenfordialtoneagain.Ifthedialtoneispresent,RJ31Xwiringiscorrect.Ifnodialtoneispresent,the

RJ31Xwiringisbackwards.RewiresodialtoneiscomingINon4and5.

If you still have trouble with the phone line, you may need to replace the RJ cord. If the dial tone is still not

present, swap out the RJ31X phone block.

To Te lephone

Line

RJ31X or RJ38X

Phone Block

Ring Tip

To Premise

Phone

Ring 1

Tip 1

Figure 11: Phone Jack Wiring

Figure 10: J1 Header and LEDs

Ethernet

Link LED

Activity LED

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 39 40

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadain XR500 Przewodnik Instalacji Strona 26

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadain XR500