Digital Monitoring Products Canadain XR500 Przewodnik Instalacji Pobierz pdf (Strona 24)

Digital Monitoring Products XR500 Series Canadian Installation Guide

InstallatIon

J23 6-Pin Header

14.1 Description

TheXR500SeriesCanadianCommandProcessor™panelsupportsRS-232,LX-Bus,andDMPWirelessoperation.Only

one operation can function at a time. Install a jumper on one pair of J23 headers to indicate how the panel is

programmedtooperate.RefertothetablebelowwheninstallingajumperonJ23.Whenajumperisinstalledor

movedonthe6-pinheader,brieyresetthepanelusingtheJ16jumpertoactivatetheselectedoperation.

Note:Onlyoneoperation,RS-232,LX-Bus,orDMPWirelesscanfunctionatatime.

J23 6-Pin Header

Letter Operation

R Standard RS-232

L LX-Bus

X 1100SeriesDMPWireless

J22 LX-Bus Expansion Connector

15.1 Description

TheXR500SeriesCanadianCommandProcessor™Panelsupportsupto500wirelessbuszonesoruptoveLX-Bus

circuits. Each Interface card LX-Bus circuit provides 100 expansion zones. The maximum number of LX-Bus zones

available on a fully populated panel is 500. Use LX-Bus J22 Header for 100 zones. Install a single Interface Card

Connectorontheboardtosupport100additionalzonesforatotalof200zones.ToinstalluptoveInterfaceCards

installaModel461InterfaceAdaptorCard.

15.2 J22 LX-Bus Header

Note: Only one connector, J21 or J22 can function at a time. Either use J21 to connect a serial device for PC Log

Reporting,oruseJ22toconnectanLX-BusorDMPWirelessdevice.Operationisdeterminedbywhereyouinstall

thejumperontheJ236-Pinheader.SeetheConnectingLX-BusandKeypadBusDevicessectionformaximumwiring

distances.

For each connection, respect wire colors when connecting devices and use all four wires. After placing the jumper

ontheJ236-Pinheadertoenabletherequiredoperation,brieyresetthepanelusingtheJ16jumpertoactivate

operation.

Wireless Bus Operation:Placeajumperonthetwopinsnexttotheletter“X”ontheJ236-Pinheader.When

usingJ22asawirelessbus,connectaDMPModel3004-wireHarnesstotheJ224-pinheaderlabeledLX.Connect

theotherendtotheJ3headeronthe1100Xor1100XHWirelessReceiver.Thisprovidesupto500wirelesszones

numbered500to999.Refertothe1100XWirelessReceiverInstallGuide(LT-0708)orthe1100XHWirelessReceiver

InstallGuide(LT-0970).

LX-Bus Operation:Placeajumperonthetwopinsnexttotheletter“L”ontheJ236-Pinheader.WhenusingJ22as

anLX-Bus,connectaDMPModel3004-wireHarnesstotheJ224-pinheaderlabeledLX.Thisprovidestherst100

LX-Bus zones numbered 500-599. No LX-Bus Interface Card is required.

Note: Do NOT use shielded wire when using the J22 LX-Bus Header.

RS-232 Operation: Place a jumper on the two pins next to the letter “R” on the J23 6-Pin header and refer to J21

Serial Connector.

Figure 8: J23 6-Pin Header

LEDs

Xmit

Rec

J22

J23

J21

RS-232

Overcurrent

(OVC) LED

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 39 40

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products Canadain XR500 Przewodnik Instalacji Strona 24

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products Canadain XR500