Digital Monitoring Products XT50 Przewodnik Instalacji Pobierz pdf (Strona 38)

XT Series Programming Guide Digital Monitoring Products

ZONE INFORMATION

This option displays when programming an 1101, 1102, 1103 OR 1106 Transmitter. Select

INT to use the internal reed switch contacts. Select EXT to connect an external device to

the transmitter’s terminal block. Default is INTERNAL.

By allowing both of the Model 1101 or 1103 transmitter contacts (INT and EXT) to be

used at the same time, two zones may be programmed from one transmitter. When using

both contacts, you must use consecutive zone numbers.

For example, program transmitter serial number 01345678 as Zone 11 with an INT

contact type and Zone 12 with an EXT contact type. The same serial number is used for

both zones.

This option displays when programming an 1114 zone expander which provides four input

contacts. Press any top row key to select the contact. Default is Contact 1.

Select the contact number to program. The same transmitter serial number is used for

all four contacts. When using the contacts, you must use consecutive zone numbers.

For example, use serial number 08345678 to program Contact 1 for Zone 21, Contact 2

for Zone 22, Contact 3 for zone 23, and Contact 4 for zone 24.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

This message displays when the Contact is already programmed for another zone. The

programmed zone number displays.

The Normally Open option only displays when EXT is selected as the Contact type. For

external devices connected to the 1101, 1102, 1103, or 1106 terminal block, select NO

to use normally closed (N/C) contacts. Select YES to use normally open (N/O) contacts.

Default is NO.

14.9.3 Supervision Time

Press any top row key to select the supervision time required for the wireless zone. Press

COMMAND to accept the default time. Default is 240 minutes.

Select the required number of minutes. The transmitter must check in at least

once during this time or a missing condition is indicated for that zone. 1100 Series

transmitters automatically checkin based on the supervision time selected for the

wireless zone, no additional programming is needed. If two zones share the same

transmitter, the last programmed supervision time is stored as the supervision time for

both zones. Zero (0) indicates an unsupervised transmitter.

The 3 minute supervision time is only available for zone types of Fire (FI), Fire Verify

(FV), and Supervisory (SV).

Note: When the panel is reset or a receiver is installed or powered down and powered

up, the supervision timer restarts for all wireless zones.

14.9.4 LED Operation

This only displays when programming a panic or pendant transmitter. Select YES to turn

a panic or pendant LED on during normal operation. Select NO to turn the LED off during

normal operation. The LED always operates on all transmitters when the transmitter

case is open and the tamper is faulted. Default is YES.

14.9.5 Disarm/Disable

Select YES to disable the zone tripped message from an 1103 Universal Transmitter

(Version 107 or higher software) or 1126/1127 PIRs during the disarmed period. When

disarmed, the transmitter or PIR only sends supervision, tamper, and low battery

messages to extend transmitter battery life. For 1103 Transmitters, a zone tripped

message is sent if the zone remains tripped for 20 seconds. Select NO to always send

zone tripped messages in addition to supervision, tamper, and low battery.

Default is YES.

14.9.6 Wireless PIR Pulse Count

This option displays for 1126 and 1127 Wireless PIRs. Select the number of infrared pulse

counts (2 or 4) the PIR will use before sending a short message. The rst infrared pulse

starts a timer and count. If no additional infrared pulses occur in 25 seconds, the timer

and count are reset. Default is 4.

14.9.7 Wireless PIR Sensitivity

This option displays for 1126 and 1127 Wireless PIRs. Select the sensitivity setting for the

PIR. Selecting LOW sets the PIR to operate at 75% sensitivity for installations in harsh

environments. Selecting HIGH sets the PIR to maximum sensitivity. Default is LOW.

INT EXT

CONTACT: 1

1 2 3 4

ALREADY USED Zxx

NORM OPEN NO YES

SUPRVSN TIME: XX

0 3 60 240

LED OPER NO YES

DISARM DISABLE

YES

WIRELESS PIR

PULSE COUNT: 4

WIRELESS PIR

SENSITIVITY: LOW

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 54 55

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products XT50 Przewodnik Instalacji Strona 38

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products XT50