Digital Monitoring Products XT50 Przewodnik Instalacji Pobierz pdf (Strona 29)

Digital Monitoring Products XT Series Programming Guide

BELL OPTIONS

Bell Options

10.1 Bell Options

This section allows you to program the panel bell output functions. If using the Model

1135 or 1135DB Wireless Siren for local annunciation, the Trip with Panel Bell option

should be selected in the Output Information programming for the siren.

10.2 Bell Cutoff Time

Enter the maximum time from 1 to 15 minutes the Bell Output remains on. If the Bell

Output is manually silenced or the system is disarmed, the cutoff time is reset. Enter

zero to provide continuous bell output. Default is 5.

Note: To support the Cancel/Verify operation on an All/Perimeter or Home/Sleep/Away

system, set the Bell Cutoff Time to greater than 0.

10.3 Automatic Bell Test

When YES is selected, the Bell Output is turned on for two seconds when all areas in the

system are armed. The Bell Test only occurs when the areas are armed from a keypad.

Arming performed from an Arming zone or remotely from Remote Link™ does not activate

the Bell Test. In addition, the Closing Wait feature is activated if Opening/Closing Reports

is YES. See OPENING/CLOSING AND USER REPORTS.

Closing Wait operation

Closing Wait provides a delay time before a monitored system arms until the panel

receives an acknowledgment of the closing report from the central station receiver.

During the delay, the keypad displays ONE MOMENT . . . Once the closing is

acknowledged, the keypad buzzes for one second and then displays the ALL SYSTEM

ON message. If the primary communication fails, but the backup communication is

successful, then the message BACKUP ALR ONLY appears. If both primary and backup

communication fail, the message LOCAL ALARM ONLY will appear.

10.4 Bell Output

Enter the output/Favorite number to follow the panel Bell terminal 5 operation for all

action and off conditions. Enter 0 (zero) to disable.

Note: When BELL ACTION below is set to T for Temporal Code 3, this Bell Output action

will be Pulse for wired outputs 1-4, wireless outputs 31-34 and 41-44.

10.5 Bell Action

This denes the type of Bell Action from zone alarms that occurs on the panel’s bell

terminal number 5. Trouble conditions do not activate Bell Action. There are seven zone

types you can program individually for Bell Output. To provide a steady Bell Output,

enter S. For a pulsed output, enter P. For a Temporal Code 3 output, enter T and for no

Bell Output, enter N.

10.5.1 Fire

Denes Bell Action for Fire Type Zones. The default is set at P.

10.5.2 Burglary

Denes Bell Action for Burglary Type Zones. The default is set at S.

10.5.3 Supervisory

Denes Bell Action for Supervisory Type Zones. The default is set at N.

10.5.4 Panic

Denes Bell Action for Panic Type Zones. The default is set at N.

10.5.5 Emergency

Denes Bell Action for Emergency Type Zones. The default is set at N.

10.5.6 Auxiliary 1

Denes Bell Action for Auxiliary 1 Type Zones. The default is set at N.

10.5.7 Auxiliary 2

Denes Bell Action for Auxiliary 2 Type Zones. The default is set at N.

BELL OPTIONS

BELL CUTOFF: 5

BELL TEST NO YES

BELL OUTPUT: 0

BELL ACTION . . .

FIRE TYPE: P

BURGLARY TYPE: S

SUPRVSRY TYPE: N

PANIC TYPE: N

EMERGNCY TYPE: N

AUXLRY 1 TYPE: N

AUXLRY 2 TYPE: N

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 54 55

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products XT50 Przewodnik Instalacji Strona 29

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products XT50