Digital Monitoring Products XR20 Przewodnik Instalacji Pobierz pdf (Strona 27)

XRSuper6/XR20/XR40 Programming Guide Digital Monitoring Products

ouTPuT oPTionS

Bell Options

7.1

BELL OPTIONS

Bell Options

This section allows you to program the panel bell output functions.

7.2

BELL CUTOFF: 5

Bell Cutoff Time

Enter the maximum time from 1 to 15 minutes the Bell Output remains on. If the

Bell Output is manually silenced or the system is disarmed, the cutoff time is reset.

Enter zero to provide continuous bell output. Default is 5.

Note: To support the Cancel/Verify operation on an All/Perimeter or Home/Sleep/

Away system, set the Bell Cutoff Time to greater than 0.

Note: For ANSI/SIA CP-01 UL installations, the Bell Cutoff Time must be set to a

minimum of six (6) minutes.

7.3

BELL TEST NO YES

Automatic Bell Test

When YES is selected, the Bell Output is turned on for two seconds when all areas

in the system are armed. The Bell Test only occurs when the areas are armed from

a keypad. Arming performed from an Arming zone or remotely from Remote Link™

does not activate the Bell Test. In addition, the Closing Wait feature is activated if

Opening/Closing Reports is YES. See OPENING/CLOSING AND USER REPORTS.

Closing Wait operation

Closing Wait provides a delay time before a monitored system arms until the

panel receives an acknowledgment of the closing report from the central station

receiver. During the delay, the keypad displays DIALING . . . Once the closing

is acknowledged, the keypad buzzes for one second and then displays the armed

message.

7.4

BELL OUTPUT:

Bell Output

Enter the output number when needed to follow the panel Bell Output operation for

all action and off conditions. Enter 0 (zero) to disable.

Note: When BELL ACTION is set to T for Temporal Code 3, the Bell Output action is

pulse.

7.5

BELL ACTION . . .

Bell Action

This denes the type of Bell Output for zone alarms. Trouble conditions do not

activate the Bell Output. There are seven zone types you can program individually

for Bell Output. To provide a steady Bell Output, enter S. For a pulsed output,

enter P. For a Temporal Code 3 output, enter T and for no Bell Output, enter N.

7.5.1

FIRE TYPE: P

Fire

Denes Bell Action for Fire Type Zones. The default is set at P.

7.5.2

BURG TYPE: S

Burglary

Denes Bell Action for Burglary Type Zones. The default is set at S.

7.5.3

SUPRVSRY TYPE: N

Supervisory

Denes Bell Action for Supervisory Type Zones. The default is set at N.

7.5.4

PANIC TYPE: N

Panic

Denes Bell Action for Panic Type Zones. The default is set at N.

7.5.5

EMERGNCY TYPE: N

Emergency

Denes Bell Action for Emergency Type Zones. The default is set at N.

7.5.6

AUXLRY 1 TYPE: N

Auxiliary 1

Denes Bell Action for Auxiliary 1 Type Zones. The default is set at N.

Note: For ANSI/SIA CP-01 UL installations, a bell action must be programmed.

7.5.7

AUXLRY 2 TYPE: N

Auxiliary 2

Denes Bell Action for Auxiliary 2 Type Zones. The default is set at N.

Note: For ANSI/SIA CP-01 UL installations, a bell action must be programmed.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 51 52

Komentarze do niniejszej Instrukcji

Brak uwag

Digital Monitoring Products XR20 Przewodnik Instalacji Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Digital Monitoring Products XR20